Installation on a shaft
Figure 1
|
Figure 2
|
Figure 3
|
Figure 4
|
Figure 5
|
Figure 6
|
Figure 7
|
Figure 8
|
Figure 9
|
Figure 10
|
Figure 11
|
Figure 1:
Mount the hub on the taper and check proper fit (see PDF download of installation instructions). Insert the long counter bolt into the thread of the set screw on the hub.
Figure 2:
Apply a few drops of loc-tite medium(blue) on the threads of the shaft-nut.
Figure 3:
Install the shaft-nut on the shaft.
Figure 4:
Tighten the shaft nut with a torque-wrench to the specified value. Use your second hand to counter hold the hub with the counter bolt.
Figure 5:
Remove the counter bolt
Figure 6:
Apply loc-tite to the hub set-screw
Mount the hub on the taper and check proper fit (see PDF download of installation instructions). Insert the long counter bolt into the thread of the set screw on the hub.
Figure 2:
Apply a few drops of loc-tite medium(blue) on the threads of the shaft-nut.
Figure 3:
Install the shaft-nut on the shaft.
Figure 4:
Tighten the shaft nut with a torque-wrench to the specified value. Use your second hand to counter hold the hub with the counter bolt.
Figure 5:
Remove the counter bolt
Figure 6:
Apply loc-tite to the hub set-screw
Figure 7:
Insert the set-screw in the same thread previously used for the counter bolt and tighten to 15 Nm.
Figure 8:
Insert the 3 bolts M8x25 with washers into the designated holes of the hub and apply again loc-tite medium(blue) to the threads.
Figure 9:
Mount the blade assembly onto the hub, carefully aligning the pins. Tighten the M8x25 bolts (25 Nm) to secure the blade assembly firmly to the hub. Then apply loc-tite low (pink) to the 3 set screws securing the M8x25 bolts.
Figure 10:
Tighten the set screws M6x10 firmly (5 Nm). Check functions of the blades. They should turn easily from stop to stop.
Figure 11:
Job done – Enjoy your new VARIPROFILE!
Insert the set-screw in the same thread previously used for the counter bolt and tighten to 15 Nm.
Figure 8:
Insert the 3 bolts M8x25 with washers into the designated holes of the hub and apply again loc-tite medium(blue) to the threads.
Figure 9:
Mount the blade assembly onto the hub, carefully aligning the pins. Tighten the M8x25 bolts (25 Nm) to secure the blade assembly firmly to the hub. Then apply loc-tite low (pink) to the 3 set screws securing the M8x25 bolts.
Figure 10:
Tighten the set screws M6x10 firmly (5 Nm). Check functions of the blades. They should turn easily from stop to stop.
Figure 11:
Job done – Enjoy your new VARIPROFILE!
Installation on a saildrive
Figure 1
|
Figure 2
|
Figure 3
|
Figure 4
|
Figure 5
|
Figure 6
|
Figure 7
|
Figure 8
|
Figure 9
|
Figure 10
|
Figure 11
|
Figure 12
|
Figure 1:
Check if your saildrive has been supplied with the appropriate distance ring between anode and propeller. If not claim from your saildrive supplier.
Figure 2:
Place the S/D hub of the VARIPROFILE on the mating teeth of the S/D shaft
Figure 3:
Apply a little loc-tite low to the threads of the shaft-nut
Figure 4:
Place it on the shaft
Figure 5:
Tighten the nut firmly by counter holding the hub with the hook-wrench supplied, inserted into the threads of the set screws.
Figure 6:
Tighten the nut with a torque-wrench to the torque values of your respective S/D supplier. Counter hold the hub with the hook-wrench supplied.
Check if your saildrive has been supplied with the appropriate distance ring between anode and propeller. If not claim from your saildrive supplier.
Figure 2:
Place the S/D hub of the VARIPROFILE on the mating teeth of the S/D shaft
Figure 3:
Apply a little loc-tite low to the threads of the shaft-nut
Figure 4:
Place it on the shaft
Figure 5:
Tighten the nut firmly by counter holding the hub with the hook-wrench supplied, inserted into the threads of the set screws.
Figure 6:
Tighten the nut with a torque-wrench to the torque values of your respective S/D supplier. Counter hold the hub with the hook-wrench supplied.
Figure 7:
Apply a little loc-tite low to the security bolt M8x20 and insert into the thread on top of the shaft nut.
Figure 8:
Tighten security bolt firmly (15 Nm) to secure the shaft nut
Figure 9:
Mount the propeller assembly unto the hub, carefully aligning the mounting holes to the hub. Apply loc-tite medium(blue) to the 3 security bolts M8x12.
Figure 10:
Tighten the security bolts firmly (15 Nm) so that the head assembly is securely fastened.
Figure 11:
Check the blade functions. They should turn easily from stop to stop.
Figure 12:
Job done – Enjoy your new VARIPROFILE!
Apply a little loc-tite low to the security bolt M8x20 and insert into the thread on top of the shaft nut.
Figure 8:
Tighten security bolt firmly (15 Nm) to secure the shaft nut
Figure 9:
Mount the propeller assembly unto the hub, carefully aligning the mounting holes to the hub. Apply loc-tite medium(blue) to the 3 security bolts M8x12.
Figure 10:
Tighten the security bolts firmly (15 Nm) so that the head assembly is securely fastened.
Figure 11:
Check the blade functions. They should turn easily from stop to stop.
Figure 12:
Job done – Enjoy your new VARIPROFILE!
